|
|
This instruction book provides information about installing and running CiscoWorks Windows on your network management station.
CiscoWorks Windows is a GUI-based device management software application that provides dynamic status, statistics, and comprehensive configuration information for Cisco Systems internetworking products.
CiscoWorks Windows allows you to display a graphical representation of each network device, display configuration and performance information, perform minor troubleshooting tasks, and control and configure specific devices.
For more information about using CiscoWorks Windows, see the CiscoWorks Windows Getting Started Guide.
This section provides CiscoWorks Windows software and hardware requirements.
You must install either Microsoft (MS) Windows 95 or Windows NT 3.51 or 4.0, TCP/IP enabled, to run Cisco Works Windows.
CiscoWorks Windows uses the native WINSOCK stacks supplied with these operating systems.
You can install CiscoWorks Windows in one of two ways:
The following components are the minimum hardware requirements for running CiscoWorks Windows:
CiscoWorks Windows can be installed as a standalone or with HP OpenView. You could use CiscoWorks Windows as a standalone in the following situations:
You could use CiscoWorks Windows with HP OpenView in the following situations:
If you are installing CiscoWorks Windows for use with HP OpenView, ensure HP OpenView is installed first, then proceed to "Installing CiscoWorks Windows." If you are installing CiscoWorks Windows as a standalone, proceed to "Installing CiscoWorks Windows."
This installation procedure performs the following functions:
Perform the following procedure to install CiscoWorks Windows:
If you are using Windows 95/Windows NT 4.0, select Start>Run, or select Start>Settings>Control Panel>Add/Remove Programs and click Install.
If you are using Windows NT 3.51, select File>Run.
d:\setup
The Welcome dialog box appears.
The User Information dialog box appears.
The Select Installation Option dialog box appears.
If you choose HP OpenView, you must have the network management platform installed; otherwise, this program exits. You can re-run the CiscoWorks Windows installation program after installing the appropriate network management platform. If you choose StandAlone, only the CiscoView and Configuration Builder applications are operational. The Choose Destination Location dialog box appears.
If either CiscoWorks Windows or CiscoVision exists on your system, you can choose to install the new version in the same directory. This automatically uninstalls the previous version. If you choose to install CiscoWorks Windows in a different directory, the previous version is not uninstalled and might not function properly.
To install devices later, choose Cancel.
The Start Copying Files dialog box appears.
The Copying Files display appears, showing you the percentage of the program successfully installed.
If the message "Not Enough Disk Space" displays, the setup program terminates. You need to free up disk space. A minimum of
130 MB is required, depending on the number of devices you install. See the section, "System Requirements" for more information. The Setup Complete dialog box appears.
For a standalone installation, you can view the README file and run CiscoView. For an HP OpenView installation, you can either restart your computer now or restart it later.
To load the MIBs into HP OpenView, continue to the section "Loading the Management Information Base (MIB)."
If you are using HP OpenView, you need to load MIBs into the HP OpenView Simple Network Management Protocol (SNMP) MIB database after installation. This allows the CiscoView and Health Monitor applications to query devices for information.
To load the MIBs, run the batch file ovmibs.bat. This file is located in the subdirectory MIBS under the directory in which HP OpenView is installed.
Some errors will be reported during the installation when loading MIBs into the HP OpenView for Windows.
For more information and workaround suggestions refer to:
http://www.cisco.com/public/mibs/app_notes/mib-compilers
or
ftp://ftpeng.cisco.com/pub/mibs/app_notes/mib-compilers
Perform the following procedure to start CiscoWorks Windows:
If you are using HP OpenView, use the HP OpenView Autodiscovery menu options to discover your network and create a network map. See the HP OpenView for Windows documentation for details.
Depending on your type of installation, the following programs are listed:
This section provides a quick reference to downloading device packages from CCO. If you do not have Internet access, skip this section (see "Additional Documentation"). For the detailed description of downloading devices, see the Software Library Web page at http://www.cisco.com/public/library.
You can access CCO as a guest or as a registered user.
To be granted special file access as a guest do the following:
Call TAC at 1-800-553-2447 or 1-408-526-7209, state the product you are using, and you are transferred to the appropriate person to obtain your special access code.
Open your Web browser and enter http://www.cisco.com/public/library
Enter your special access code in the Other Software Products/Special Files section.
Select the device tar file and a download option.
Reenter your password, if required.
Save the device file in the cv_pkgs directory on your PC.
Go to Step 7, "UnZip the device tar file."
To access as a registered user do the following:
Open your Web browser and access the Software Image Library by typing:
http://www.cisco.com/kobayashi/Library_root.shtml
At the prompts, enter your CCO user ID and password.
Proceed to Step 6, "Download the device tar file into the cv_pkgs directory."
There are two methods for downloading, downloading from CCO and downloading from FTP. For information on downloading from FTP, see the Software Library Web page or the CiscoWorks Windows Getting Started Guide.
In the Software Image Library Network Management Products section, select the CiscoView Upgrade Planner pointer to the CiscoView packages.
To review the package README, click on the README filename and select a download option.
To select a device tar file, click on the device filename and select a download option.
Reenter your password, if required.
If required, click Save File or File>Save As, depending on the browser you are using. If a filter window appears, enter the complete destination pathname for the downloaded device.
If a filter window appears, enter the complete destination pathname in the Selection section of the filter window for the downloaded device, for example, c:\cv_pkgs\device_name.
Close the Web browser.
Go to Step 7, "UnZip the device tar file."
If you are using Windows 95 or Windows NT 4.0, select Start>Programs>WinZip 6.1 32-bit to start WinZip.
If you are using Windows NT 3.51, select File>Run>WinZip.
Select the Open icon on the WinZip main menu.
In the Look in field, select the drive and directory (c:\cv_pkgs) containing the device file.
Select the tar file, then Open.
Select the Extract icon.
In the Extract dialog box, select All files and Overwrite Existing Files.
Make sure the Extract To directory is correct, for example, c:\cv_pkgs.
Click Extract.
Close WinZip.
Windows NT 3.51
Return to the Program Manager and restore CiscoWorks Windows by clicking it icon.
Double-click the Install Device icon. The Setup program starts.
Go to the directory containing the package file (c:\cv_pkgs).
Select the device package you want to load, click OK.
Windows 95/Windows NT 4.0
Select the Task Bar Start menu.
Click the Programs folder.
Click CiscoWorks Windows.
Click Install Device. The Setup program starts
In the Select Package dialog box, select the directory containing the package file (c:\cv_pkgs).
Select the device package you want to load; click OK.
For Standalone:
Select the CiscoView icon from the CiscoWorks Window program group.
Use File>Open Device to view your device.
For Non-Standalone:
Double-click on the CiscoWorks icon in the CiscoWorks program group.
Double-click on the device you just installed.
The downloading is complete. If there are any problems, check the CVinstall.log file in your install directory or see the CiscoWorks Windows Getting Started Guide for more detail.
The CiscoWorks Windows Getting Started Guide contains information on the following:
Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.
CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.
You can access CCO in the following ways:
For a copy of CCO's Frequently Asked Questions (FAQ), contact ccohelp@cisco.com. For additional information, contact cco-team@cisco.com.
If you are a network administrator and need personal technical assistance with a Cisco product that is under warranty or covered by a maintenance contract, contact Cisco's Technical Assistance Center (TAC) at 800 553-2447, 408 526-7209, or tac@cisco.com. To obtain general information about Cisco Systems, Cisco products, or upgrades, contact 800 553-6387, 408 526-7208, or cs-rep@cisco.com
|
|