cc/td/doc/product/access/acs_mod/1600
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Hardware Specifications and Cable Pinouts

Hardware Specifications and Cable Pinouts

This appendix contains the following sections:

Hardware Specifications

Table C-1 lists the system specifications for Cisco 1600 series routers.


Table  C-1: System Specifications
Description Specification
Processor Motorola MC68360 QUICC (33 MHz)
Dimensions

  • Height

  • Width

  • Depth

2.19 inches (5.56 centimeters)

11.15 inches (28.32 centimeters)

8.67 inches (22.02 centimeters)

Weight

  • Minimum (no WAN interface card installed)

  • Maximum

1.65 pounds (0.75 kilograms)

1.80 pounds (0.82 kilograms)

Power (external) 14 VDC (+ / - 8%), minimum 1A
Console port RJ-45 connector
10BaseT port RJ-45 connector
AUI port DB-15 connector
Flash memory slot Flash PC card
Serial port (Cisco 1601) DB-60 connector
DSU/CSU port (Cisco 1602) RJ-48S connector
ISDN ports1 (Cisco 1603 and Cisco 1604) RJ-45 connector
Temperature

  • Operating

  • Nonoperating

32 to 104×F (0 to 40×C)

-4 to 149×F (-20 to 65×C)

Operating humidity 5 to 95%, noncondensing

1 ISDN ports refer to the ISDN S/T and the ISDN U ports.

Cable Pinouts

This section includes the following pinouts:


Table  C-2: 10BaseT Port Pinouts
8 Pin1 Description
1 TX+
2 TX-
3 RX+
6 RX-

Table  C-3: Straight-Through 10BaseT Cable (RJ-45 to RJ-45) Pinouts
RJ-45
Pin 		Signal Direction RJ-45
Pin
1 TX+ --> 1
2 TX- --> 2
3 RX+ <-- 3
4 - - 4
5 - - 5
6 RX- <-- 6
7 - - 7
8 - - 8

The EIA/TIA-232 console port is configured as data terminal equipment (DTE) and uses an RJ-45 connector. A console cable kit is provided with your router to connect a console (an ASCII terminal or PC running terminal emulation software) to the console port. The console cable kit contains an RJ-45-to-RJ-45 roll-over cable and a RJ-45-to-DB-25 female DTE adapter (labeled Terminal). Table C-4 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable, and the RJ-45-to-DB-25 female DTE adapter.


Table  C-4: Console Cable and Adapter Pinouts
Console Port (DTE) RJ-45-to-RJ-45 Roll-Over Cable
Signal RJ-45 Pin RJ-45 Pin DB-9 Pin DB-25 Pin Signal
- 1 8 7 4 -
DTR 2 7 4 20 DSR
TxD 3 6 3 2 RxD
GND 4 5 5 7 GND
GND 5 4 5 7 GND
RxD 6 3 2 3 TxD
DSR 7 2 6 6 DTR
- 8 1 8 5 -

You can identify a roll-over cable by comparing the two modular ends of the cable. (See Figure C-1.) Holding the cables in your hand, side-by-side, with the tab at the back, the wire connected to the pin on the outside of the left connector (pin 1) should be the same color as the pin on the outside of the right connector (pin 8). On Cisco cables, pin 1 is white on one connector, and pin 8 is white on the other connector.


Figure C-1: Identifying a Rollover Cable




Table  C-5: 56-kbps CSU/DSU (RJ-48S) Pinouts
8 Pin2 Description
1 Transmit
2 Transmit
7 Receive
8 Receive

Table  C-6: ISDN BRI S/T Port Pinouts (RJ-45)
8 Pin3 TE1 NT2 Polarity
3 Transmit Receive +
4 Receive Transmit +
5 Receive Transmit -
6 Transmit Receive -

1 TE refers to terminal terminating layer 1 aspects of TE1, TA, and NT functional groups. This applies to the Cisco 1603 and the ISDN BRI S/T WAN interface card.
2 NT refers to network terminating layer 1 aspects of NT1 and NT2 functional groups. This applies to the Cisco 1604 ISDN S/T port.

Table  C-7: ISDN BRI U Port Pinouts (RJ-45)
8 Pin4 Function
3 No connection
4 Signal--Tip or Ring
5 Signal--Tip or Ring
6 No connection

The serial port on the router uses a universal port, a 60-pin receptacle that supports the following serial interfaces: EIA/TIA-232, EIA/TIA-449, X.21, V.35, and EIA-530. The shielded serial transition cable determines the electrical interface type. The router end of all of the cables is a 60-pin connector.

DTE connectors have a plug connector at the network end. (DCE connectors have a receptacle at the network end.) However, V.35 is available in DTE mode with a connector of either gender at the network end. The serial port operates in DTE and DCE modes.

The tables that follow list the signal pinouts for the DTE mode serial transition cables for each router interface type.

Figure C-2 shows the EIA/TIA-232 serial cable assembly, and Table C-8 lists the EIA/TIA-232 cable pinouts.


Figure C-2: EIA/TIA-232 Serial Cable Assembly




Table  C-8: EIA/TIA-232 DTE Cable Pinouts (DB-60 to DB-25)
60 Pin5 Signal Description Direction 25 Pin Signal
J1-50
J1-51
J1-52 		MODE_0
GND
MODE_DCE 		Shorting group - - -
J1-46 Shield GND Single - J2-1 Shield GND
J1-41
Shield 		TxD/RxD
- 		Twisted pair no. 5 -->
- 		J2-2
Shield 		TxD
-
J1-36
Shield 		RxD/TxD
- 		Twisted pair no. 9 <--
- 		J2-3
Shield 		RxD
-
J1-42
Shield 		RTS/CTS
- 		Twisted pair no. 4 -->
- 		J2-4
Shield 		RTS
-
J1-35
Shield 		CTS/RTS
- 		Twisted pair no. 10 <--
- 		J2-5
Shield 		CTS
-
J1-34
Shield 		DSR/DTR
- 		Twisted pair no. 11 <--
- 		J2-6
Shield 		DSR
-
J1-45
Shield 		Circuit GND
- 		Twisted pair no. 1 -
- 		J2-7
Shield 		Circuit GND
-
J1-33
Shield 		DCD/LL
- 		Twisted pair no. 12 <--
- 		J2-8
Shield 		DCD
-
J1-37
Shield 		TxC/NIL
- 		Twisted pair no. 8 <--
- 		J2-15
Shield 		TxC
-
J1-38
Shield 		RxC/TxCE
- 		Twisted pair no. 7 <--
- 		J2-17
Shield 		RxC
-
J1-44
Shield 		LL/DCD
- 		Twisted pair no. 2 -->
- 		J2-18
Shield 		LTST
-
J1-43
Shield 		DTR/DSR
- 		Twisted pair no. 3 -->
- 		J2-20
Shield 		DTR
-
J1-39
Shield 		TxCE/TxC
- 		Twisted pair no. 6 -->
- 		J2-24
Shield 		TxCE
-

Figure C-3: EIA/TIA-449 Serial Cable Assembly




Table  C-9: EIA/TIA-449 DTE Cable Pinouts (DB-60 to DB-37)
60 Pin6 Signal Description Direction 37 Pin Signal
J1-49
J1-48 		MODE_1
GND 		Shorting group - - -
J1-51
J1-52 		GND
MODE_DCE 		Shorting group - - -
J1-46 Shield_GND Single _ J2-1 Shield GND
J1-11
J1-12 		TxD/RxD+
TxD/RxD- 		Twisted pair no. 6 -->
--> 		J2-4
J2-22 		SD+
SD-
J1-24
J1-23 		TxC/RxC+
TxC/RxC- 		Twisted pair no. 9 <--
<-- 		J2-5
J2-23 		ST+
ST-
J1-28
J1-27 		RxD/TxD+
RxD/TxD- 		Twisted pair no. 11 <--
<-- 		J2-6
J2-24 		RD+
RD-
J1-9
J1-10 		RTS/CTS+
RTS/CTS- 		Twisted pair no. 5 -->
--> 		J2-7
J2-25 		RS+
RS-
J1-26
J1-25 		RxC/TxCE+
RxC/TxCE- 		Twisted pair no. 10 <--
<-- 		J2-8
J2-26 		RT+
RT-
J1-1
J1-2 		CTS/RTS+
CTS/RTS- 		Twisted pair no. 1 <--
<-- 		J2-9
J2-27 		CS+
CS-
J1-44
J1-45 		LL/DCD
Circuit_GND 		Twisted pair no. 12 -->
_ 		J2-10
J2-37 		LL
SC
J1-3
J1-4 		DSR/DTR+
DSR/DTR- 		Twisted pair no. 2 <--
<-- 		J2-11
J2-29 		DM+
DM-
J1-7
J1-8 		DTR/DSR+
DTR/DSR- 		Twisted pair no. 4 -->
--> 		J2-12
J2-30 		TR+
TR-
J1-5
J1-6 		DCD/DCD+
DCD/DCD- 		Twisted pair no. 3 <--
<-- 		J2-13
J2-31 		RR+
RR-
J1-13
J1-14 		TxCE/TxC+
TxCE/TxC- 		Twisted pair no. 7 -->
--> 		J2-17
J2-35 		TT+
TT-
J1-15
J1-16 		Circuit_GND
Circuit_GND 		Twisted pair no. 9 -
- 		J2-19
J2-20 		SG
RC

Figure C-4: X.21 Cable Assembly




Table  C-10: X.21 DTE Cable Pinouts (DB-60 to DB-15)
60 Pin7 Signal Description Direction 15 Pin Signal
J1-48
J1-47 		GND
MODE_2 		Shorting group - - -
J1-51
J1-52 		GND
MODE_DCE 		Shorting group - - -
J1-46 Shield_GND Single - J2-1 Shield GND
J1-11
J1-12 		TxD/RxD+
TxD/RxD- 		Twisted pair no. 3 -->
--> 		J2-2
J2-9 		Transmit+
Transmit-
J1-9
J1-10 		RTS/CTS+
RTS/CTS- 		Twisted pair no. 2 -->
--> 		J2-3
J2-10 		Control+
Control-
J1-28
J1-27 		RxD/TxD+
RxD/TxD- 		Twisted pair no. 6 <--
<-- 		J2-4
J2-11 		Receive+
Receive-
J1-1
J1-2 		CTS/RTS+
CTS/RTS- 		Twisted pair no. 1 <--
<-- 		J2-5
J2-12 		Indication+
Indication-
J1-26
J1-25 		RxC/TxCE+
RxC/TxCE- 		Twisted pair no. 5 <--
<-- 		J2-6
J2-13 		Timing+
Timing-
J1-15
Shield 		Control_GND
- 		Twisted pair no. 4 -
- 		J2-8
Shield 		Control GND
-

Figure C-5: V.35 Cable Assembly




Table  C-11: V.35 Cable Pinouts (DB-60 to 34-Pin)
60 Pin8 Signal Description Direction 34 Pin Signal
J1-49
J1-48 		MODE_1
GND 		Shorting group - - -
J1-50
J1-51
J1-52 		MODE_0
GND
MODE_DCE 		Shorting group - - -
J1-53
J1-54
J1-55
J1-56 		TxC/NIL
RxC_TxCE
RxD/TxD
GND 		Shorting group - - -
J1-46 Shield_GND Single - J2-A Frame GND
J1-45
Shield 		Circuit_GND
- 		Twisted pair no. 12 -
- 		J2-B
Shield 		Circuit GND
-
J1-42
Shield 		RTS/CTS
- 		Twisted pair no. 9 -->
- 		J2-C
Shield 		RTS
-
J1-35
Shield 		CTS/RTS
- 		Twisted pair no. 8 <--
- 		J2-D
Shield 		CTS
-
J1-34
Shield 		DSR/DTR
- 		Twisted pair no. 7 <--
- 		J2-E
Shield 		DSR
-
J1-33
Shield 		DCD/LL
- 		Twisted pair no. 6 <--
- 		J2-F
Shield 		RLSD
-
J1-43
Shield 		DTR/DSR
- 		Twisted pair no. 10 -->
- 		J2-H
Shield 		DTR
-
J1-44
Shield 		LL/DCD
- 		Twisted pair no. 11 -->
- 		J2-K
Shield 		LT
-
J1-18
J1-17 		TxD/RxD+
TxD/RxD- 		Twisted pair no. 1 -->
--> 		J2-P
J2-S 		SD+
SD-
J1-28
J1-27 		RxD/TxD+
RxD/TxD- 		Twisted pair no. 5 <--
<-- 		J2-R
J2-T 		RD+
RD-
J1-20
J1-19 		TxCE/TxC+
TxCE/TxC- 		Twisted pair no. 2 -->
--> 		J2-U
J2-W 		SCTE+
SCTE-
J1-26
J1-25 		RxC/TxCE+
RxC/TxCE- 		Twisted pair no. 4 <--
<-- 		J2-V
J2-X 		SCR+
SCR-
J1-24
J1-23 		TxC/RxC+
TxC/RxC- 		Twisted pair no. 3 <--
<-- 		J2-Y
J2-AA 		SCT+
SCT-

Figure C-6: EIA-530 Cable Assembly




Table  C-12: EIA-530 DTE Cable Pinouts (DB-60 to DB-25)

60 Pin9
Signal
25 Pin
Signal 		Direction
DTE  DCE1
J1-11
J1-12 		TxD/RxD+
TxD/RxD- 		J2-2
J2-14 		BA(A), TxD+
BA(B), TxD- 		-->
-->
J1-28
J1-27 		RxD/TxD+
RxD/TxD- 		J2-3
J2-16 		BB(A), RxD+
BB(B), RxD- 		<--
<--
J1-9
J1-10 		RTS/CTS+
RTS/CTS- 		J2-4
J2-19 		CA(A), RTS+
CA(B), RTS- 		-->
-->
J1-1
J1-2 		CTS/RTS+
CTS/RTS- 		J2-5
J2-13 		CB(A), CTS+
CB(B), CTS- 		<--
<--
J1-3
J1-4 		DSR/DTR+
DSR/DTR- 		J2-6
J2-22 		CC(A), DSR+
CC(B), DSR- 		<--
<--
J1-46
J1-47 		Shield_GND
MODE_2 		J2-1
- 		Shield
- 		Shorted
J1-48
J1-49 		GND
MODE_1 		-
- 		-
- 		Shorted
J1-5
J1-6 		DCD/DCD+
DCD/DCD- 		J2-8
J2-10 		CF(A), DCD+
CF(B), DCD- 		<--
<--
J1-24
J1-23 		TxC/RxC+
TxC/RxC- 		J2-15
J2-12 		DB(A), TxC+
DB(B), TxC- 		<--
<--
J1-26
J1-25 		RxC/TxCE+
RxC/TxCE- 		J2-17
J2-9 		DD(A), RxC+
DD(B), RxC- 		<--
<--
J1-44
J1-45 		LL/DCD
Circuit_GND 		J2-18
J2-7 		LL
Circuit_ GND 		-->
-
J1-7
J1-8 		DTR/DSR+
DTR/DSR- 		J2-20
J2-23 		CD(A), DTR+
CD(B), DTR- 		-->
-->
J1-13
J1-14 		TxCE/TxC+
TxCE/TxC- 		J2-24
J2-11 		DA(A), TxCE+
DA(B), TxCE- 		-->
-->

1 The EIA-530 interface cannot be operated in DCE mode. A DCE cable is not available for the EIA-530 interface.


1 Pins 4, 5, 7, and 8 are not used.
2 Pins 3, 4, 5, and 6 are not used.
3 Pins 1, 2, 7, and 8 are not used.
4 Pins 1, 2, 7, and 8 are not used.
5 &&Center&&Any pin not referenced is not connected.
6 &&Center&&Any pin not referenced is not connected.
7 Any pin not referenced is not connected.
8 &&Center&&Any pin not referenced is not connected.
9 &&Center&&Any pin not referenced is not connected.

hometocprevnextglossaryfeedbacksearchhelp
Copyright 1989-1997 © Cisco Systems Inc.